Saffire mixcontrol program9/20/2023 ![]() ![]() ![]() The eight award-winning Focusrite microphone pre-amps work together with a quality digital conversion system that features JetPLL jitter elimination technology. However, the Saffire PRO 40 MixControl software is not required for the unit's operation or its use with any DAW software such as Pro Tools 9. Your setup and settings in the Saffire MixControl software can be saved to the firmware of the Saffire Pro 40 allowing the unit to run standalone-without being connected to a computer. This is easily setup using its included 18 X 16 DSP mixer/routing software called Saffire MixControl. With its flexible analog and digital I/O capabilities the PRO 40 acts as the "nexus" of your DAW studio-it also can act as a "breakout box" for an ADAT deck or any digital system connected via the ADAT or SPDIF facilities. The Focusrite Saffire 40 stands out from other manufacturer's units chiefly because of its superior analog front end, solid digital conversion system, unique feature set, and the unit's seemingly endless universality. Goodluck, again, not at my rig right now, so I may be a little off in my setup.The single rackspace Focusrite Saffire PRO 40 is part of the Saffire line of Firewire audio/MIDI interfaces that all feature innovative control, routing and, in the case of the PRO 40, latency-free direct monitoring. My suggestion is that you make some of your cue sends mono if you want 6. I think you're going to run into limitations with only a Saffire 40, outs 1/2 are your monitor outs. Once you have it working Save that setup as a template in your Mix Control software. Typically DAW 1/2 is your main out, so any other out you set up will be DAW 3/4 for aux 1, DAW 5/6 for aux 2 etc.I'm not at my rig so I'm just going from memory. ONce that's done, go to your Mix control and set the output sections to follow the appropriate settings. This is where things may take some tinkering. You'll need to setup stereo outputs in Pro Tools in your i/o settings and label them appropriately.įrom there, you can set up AUx sends from your tracks and assign the AUx buss output to the appropriate outputs you created in the I/o settings. You'll still need to utilize the Mix control to set up your outputs on your saffire device. ![]() If that's the case, then you should be able to set up cue sends the same way you would on an analogue desk. That you are then, you're system is clearly a bit more of a monster than my MBP. What you set up in the mixer section of Saffire MixControl only affects what is heard in the outputs." The mixes you create do not affect how the audio inputs are routed to the DAW, nor does it affect the audio level of the signal to be recorded. The Mixer Section is used to create mixes for monitoring purposes. Up to 16 mono mixes or 8 stereo mixes, (or any combination of mono and stereo mixes,) are available, making up a total of 16 mix channels.Įach Mix can contain up to 18 of the possible 40 inputs signals, and each mix can be sent to any number of outputs.Įach mix shares the same source inputs, but all other mixer controls are independent in each mix. "The Saffire MixControl software includes a total of 16 mixes, each with a maximum of 18 channels in the mix. All inputs on the Saffire PRO 40 are routed directly to your DAW software for recording, but Saffire MixControl also allows you to route these signals to your monitors so that you can listen to the audio signals with zero latency - before they arrive at your DAW." "Saffire MixControl software provides mixing and routing to and from the DAW, allowing control over which signals are sent from the sequencer to each output. I'm still new with my Pro 40 but you can do multiple headphone mixes with no latency. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |